Arduino Software Compatible Boards

Iduino Uno

The Iduino Uno is an Arduino with the through-hole ATmega328, and appears to be an exact copy of the Arduino Uno.

Read more

MLT Group Fino

Fino (Arduino Compatible) Board is a microcontroller board based on the ATmega328 microcontroller with duemilanove bootloader. It has the pre 1.0 pinout, and an FTDI USB to TTL converter. An onboard switch can disable DTR reset and the L LED.

Read more

Funduino Uno R3

The Funduino Uno R3 is an Arduino Uno R3 with the through-hole ATmega328. It duplicates the Arduino Uno R3 en about every way.

Read more

Microduino Core+

Microduino-Core+ is one of core modules of Microduino series, using Atmel ATmega644PA/ATmega1284P series as main chip, it is a performance enhanced version of Microduino-Core.Microduino uses optiboot for bootloader, it takes less Flash than Arduino default engine and optimizes program uploading.

Read more

Meduino Nano V3

The Meduino Nano is a Nano clone with a switch selectable supply voltage - 3.3V or 5V. Because of the switch, the board is a little bit longer than a typical Nano, but the pinout is identical.

Read more

Really Bare Bones Board (BBB) Kit

The Really Bare Bones Board (RBBB) is a mini board designed for those experimental applications that require small processors, such as wearable computing, near space experiments, toy prototyping, artist projects or any use for a fairly small, low-cost microcontroller.

Read more

Sparkfun ProtoSnap

Sparkfun came up with a single snappable board that has an Arduino Pro Mini, FTDI breakout, buzzer, RGB LED, light sensor, push button and proto area. When you are comfortable with it, you can snap the boards apart.

Read more

pcbprotos Turk Nano

The Turk Nano v3 is a small board based on the ATmega328. It is an exact copy of the Arduino Nano, using the original PCB files.

Read more

EtherMega

The Freetronics EtherMega is a merger between the Arduino Mega 2560 and the Freetronics Ethernet Shield. It features an ATmega2560, Wiznet with PoE, a micro-SD slot, and a gold plated PC Board.

Read more

Evil Mad Scientist Labs Diavolino

This is a very Arduino-Pro-like board. Completely stripped down for embedded use. Very stylish, too.

Read more

Freaduino Uno

The Freaduino Uno is an Uno clone with a few enhancements that make it easier to use with sensors and breakout boards.

Read more

Deek-Robot Pro Mini

The Deek-Robot Pro Mini is the most available Arduino Pro Mini clone. The Deek-Robot Pro Mini has no I/O connectors, or USB to Serial converter. It is available in a 16MHz / 5V version only.

Read more

EtherTen

The Freetronics EtherTen is a merger between their "Eleven" and "Ethernet Shield". It features an ATmega328P, PoE built in, a micro-SD slot, and a gold plated PC Board.

Read more

Funduino Leonardo Pro Micro

The Funduino Leonardo Pro Micro is similar to the Sparkfun Pro Micro, in that it uses the ATmega32u4, with built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard.

Read more

PJRC Teensy LC

The Teensy LC is based on the the ARM Cortex-M0+ MCU, and is priced at less than US$12.

Read more

Gboard Pro

Gboard Pro is a unique Arduino mainboard with SIM900 GSM / GPRS module, XBee socket, nRF24L01 + module interface, micro SD card interface, ITDB02 parallel LCD module interface, electronic brick interface and ATmega2560. It supports XBee, nRF24L01 + or GSM / GPRS with functions from smart home to remote control.

Read more

AsyncLabs Black Widow 1.0

The AsyncLabs Black Widow 1.0 is an Arduino Duemilanove clone with 802.11b wireless (WiFi) onboard.

Read more

Iduino Nano

The Iduino Nano v3 is a small board based on the ATmega328. It copies the Gravitech Arduino Nano almost exactly.

Read more

Seeeduino 4.2

The Seeeduino 4.2 is an Uno R3 type board with a more efficient power supply, selectable to 3.3V or 5V, and with three Grove-type connectors.

Read more

Sparkfun Red Board

The Redboard is a meld of different versions of the Arduino. It has the older FTDI USB to Serial converter, and the newer R3 pinout.

Read more

Sparkfun Pro Micro

The Sparkfun Pro Micro is similar to the Arduino Leonardo in that the ATmega32u4 has built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard. The Pro Micro differs from the micro in that it has fewer I/O lines, no ICSP connector, and no reset switch.

Read more

Funduino Mega 2560

The Funduino Mega2560 has an ATmega2560 MCU, and the larger Mega form factor. It has 54 I/O lines, with 15 of them capable of PWM and 16 analog input lines.

Read more

InHaos Buono Lite R3

The InHaos Buono Lite R3 is based on the InHaos Buono R3 SMD. It can run at either 5V or 3.3V (switch selectable), with an enhanced regulator for a wider 6V to 23V input range. It does not have a USB to serial connection, but uses an external USB converter cable.

Read more

SolarBotics SB Ardweeny

The Ardweeny is a board that piggybacks onto the ATmega328, making it very small. At approximately $10, it is a real bargain, too.

Read more

DFRduino Uno R3

The DFRduino Uno R3 is an almost exact replica of the through-hole Arduino Uno R3. It has color coded socket connectors to keep it interesting, but it is otherwise an Uno R3.

Read more

PJRC Teensy 3.1

The Teensy 3.1 is a tiny little board, intended for standalone or breadboard use, supported by several useful plugin modules, and sporting a 96MHz (overclockable) Arm Cortex M4 with 256kB Flash, 64kB RAM, and 2kB EEPROM. It is an Arduino compatible in that the software can be written in the Arduino IDE. Very inexpensive compared with the Arduino Uno.

Read more

LinkSprite WiFi Diamondback

The WiFi DiamondBack 1.0 is an Arduino Uno compatible that has built-in WiFi. It is 100% compatible with the Asynclab BlackWidow.

Read more

Bare Bones Board (BBB) Kit

The Bare Bones Board (BBB) is an Arduino-compatible board (Freeduino) that implements the functionality of the Arduino Duemilanove/Diecimila, on a smaller printed circuit board, by removing the USB communications chip to another board.

Read more

PJRC Teensy 2.0

The Teensy 2.0 is based on the the ATmega32U4 MCU, and is small. 0.7" by 1.2" small.

Read more

SainSmart Due

The SainSmart Due is the first Arduino to use a non-ATmega chip, although the ATSAM3X8E is an Atmel made Arm Cortex M3. The MCU runs at 84MHz. It is pin-compatible with the Arduino Mega boards, but is 3.3V only. Only 3.3V shields will work. 5V shields will probably damage the board.

Read more

ATmega128RFA1 Development Board

The Sparkfun ATmega128RFA1 Development Board is a "Pro-like" board for the ATmega128RFA1 MCU from Atmel. The ATmega128RFA1 is a 2.4GHz IEEE 802.15.4 compatible transceiver merged with an ATmega128 MCU.

Read more

AVR.duino U+

The AVR.duino U+ is a board designed by SlicMicro that incorporates the standard Arduino Uno R3 features with the addition of a pot, button, and LED. Also, A6 and A7 are brought out to pads.

Read more

USB BoArduino

The USB BoArduino is similar to "genuine" Arduino boards in function, and is software compatible with the Arduino Uno board. It is made specifically for use on a breadboard. Everyone should have one of these things for breadboard use. Find out why...

Read more

SainSmart Mega 2560 R3

The SainSmart Mega2560 R3 is a clone of the Arduino Mega2560 R3, having the new R3 pinout.

Read more

FreakLabs Freakduino v2.1a

The Freakduino is a niche Arduino compatible designed with RF communication in mind. The board comes in several versions, based on the frequency and/or range of the radio. Frequencies are 2.4GHz and 900MHz, with two power ranges available in the 900MHz version.

Read more

Seeeduino Mega

The Seeeduino Mega is not like other Megas. It has a slightly smaller form factor and a whole lot more I/O.

Read more

Eleven

The Freetronics Eleven is a well thought out and executed clone of the Arduino Uno. It features an ATmega328P, a micro USB connector, a prototyping area, and a gold plated PC Board.

Read more

SainSmart Mega 2560

The SainSmart Mega2560 has an ATmega2560 MCU, and the larger Mega form factor. It has 54 I/O lines, with 15 of them capable of PWM and 16 analog input lines.

Read more

Stanford University Hapkit

Hapkit is an open-hardware haptic device designed to be very low-cost and easy to assemble. Hapkit allows users to input motions and feel programmed forces in one degree of freedom.

Read more

Iteaduino MEGA 2560

Iteaduino MEGA2560 is a derivative of the Arduino MEGA 2560. It is shield compatible with the Uno, but NOT with the Arduino Mega.

Read more

Iteaduino BT

Iteaduino-BT is an Arduino compatible board with a master/slave Bluetooth Module HC-05. It is based on the Arduino UNO/Duemilanove, but with added bluetooth.

Read more

Anarduino Mini

The Anarduino Mini has features similar to the Arduino Mini, but with a pad location underneath for an RFM73 2.4GHz module. It has no RAW input, and no regulator, so you have to supply 5V directly.

Read more

Microduino Core

Microduino uses the same development environment as Arduino IDE, designers can use the Arduino IDE, Processing on Microduino for idea realization, prototype development and low volume production.

Read more

Sparkfun Mega Pro

The Sparkfun Mega Pro is a Sparkfun "Pro" version of the Arduino Mega 2560. Like the Pro and Pro Mini, it has no USB to TTL converter, and no headers. Other than that it is a full blown ATmega2560.

Read more

DC BoArduino

The DC BoArduino is similar to "genuine" Arduino boards in function, and is software compatible with the Diecimila/Duemilanove boards. It is made specifically for use on a breadboard. Everyone should have one of these things for breadboard use.

Read more

SainSmart Uno R3

The SainSmart Uno R3 is an Arduino Uno R3 with the through-hole ATmega328. It duplicates the Arduino Uno R3 en about every way.

Read more

PJRC Teensy++ 2.0

The Teensy++ 2.0 is based on the the AT90USB1286 MCU, and is larger at 0.7" by 2.0" than the Teensy 2.0. Larger because it has 46 I/O lines. 8 analog I/O. The AT90USB1286 has 128kB Flash, 8kB RAM, and 4kB EEPROM.

Read more

InHaos Buono R3

The InHaos Buono is based on the Arduino Uno R3 SMD. It can run at either 5V or 3.3V (switch selectable), with an enhanced regulator for a wider 6V to 23V input range.

Read more

eNTuino

The eNTuino ATmega328 is an Arduino Uno clone with some improvements, including battery charging circuitry, and a dual header pinout.

Read more

Funduino Pro Mini

The Funduino Pro Mini is similar to the Sparkfun Pro Mini, having an ATmega328P and no USB converter. It does have additional I/O pads on one end.

Read more

Deek-Robot Pro Micro

The Deek-Robot Pro Micro is similar to the Sparkfun Pro Micro, in that it uses the ATmega32u4, with built-in USB communication, eliminating the need for a secondary processor. This allows the Micro to appear to a connected computer as a mouse and keyboard. The Deek Robot Pro Micro appears to be a perfect clone of the Sparkfun Pro Micro. The Arduino add-on files are actually named "SF32u4_boards.zip"

Read more

DFRduino FIO

The DFRduino Funnel I/O (Fio) is a board based on the original design of the Arduino FIO. It is 100% compatible with original Arduino FIO.Funnel is a toolkit to sketch your idea physically, and consists of software libraries and hardware. By using Funnel, the user can interface to sensors and/or actuators with various programming languages such as ActionScript 3, Processing, and Ruby.

Read more

SainSmart Leonardo R3

The SainSmart Leonardo R3 is a clone of the Arduino Leonardo R3, a return to the simplified model of the Pro, using an ATmega32U4 as the MCU and USB interface. The main advantage of this design is the ability for the SainSmart Leonardo to appear to the computer to be an HID (keyboard or mouse), rather than only as a serial port. The R3 version has the R3 pinout.

Read more

Iduino Pro Mini

The Iduino Pro Mini is made by GE Tech in Shenzen, and is a copy of the Sparkfun Arduino Pro Mini.

Read more

DFRduino Pro Mini V1.3

The 5V DFRduino Pro Mini V1.3 (Arduino Pro Mini Compatible) is a microcontroller board based on the ATmega328. It is a 5V DFduino running the 16MHz bootloader (select Arduino Duemilanove w/ 328 within the Arduino software). It is an advance version of offical Arduino Pro Mini. The DFRduino Pro mini has 8 analog inputs compared with offical 6. The rest bits are exactly the same. The pin layout is compatible with the Arduino Mini.

Read more

SainSmart Mega ADK

The SainSmart Mega ADK is an Arduino Mega 2560 with a USB host controller and connector for communication with an Android device. It has a beefier voltage regulator to supply charging current to the attached Android device.

Read more

RepRap Champion Uno

The RepRap Champion Uno baord has some nice features. It costs $6.00. It has an extra pad for each I/O line.It has a header for all of the serial lines. It has something not so good, too...

Read more

SolarBotics SB Freeduino

The Freeduino is a board similar to the Arduino Decimila, but as a partial kit.

Read more

Makeblock Me Orion

The Makeblock Me Orion is a merging of the Meduino Uno and the Me Base Shield. It has no Arduino headers (it doesn't really need them) and is compatible with the Arduino and Scratch environments.

Read more

DFRobot Bluno

It is time to get Bluetooth 4.0 into your project, together with your phone! For aficionados of smart devices and wearables, now you can go further than hacking things bought in the market to building your own prototype out of garage. The Bluno board is first of its kind in intergrating BT 4.0(BLE) module into Arduino Uno, making it an ideal prototyping platform for both software and hardware developers to go wireless. You will be able to develope your own smart bracelet , smart pedometer and more. Through the low- power Bluetooth 4.0 technology, real-time low energy communication can be made really easy.

Read more

Meduino Uno R3

The Meduino Uno R3 is an Uno clone, typical of the Uno clones. They have PCB artwork that is nearly identical to the Arduino Uno, but with dead-end feedthroughs missing. Most Counterfeit Unos look similar, but the Meduino does not claim to be an Arduino.

Read more
Arduino Board Logo

 

Arduino-Board is the go-to source for information on many available Arduino and Arduino-like boards, tutorials and projects.

Help and Support

Arduino-Board

Stay updated

Sign up if you would like to receive our once monthly newsletter.